ProBoat Impulse 31 PRB4250B Instrukcja Obsługi Strona 5
- Strona / 40
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
5
EN
Impulse 26
1. Lift the back of the hatch and pull the hatch backward to remove.
2. Remove the radio box cover.
2
3. Put hook tape inside the boat hull as shown.
4. Put loop tape on the boat battery. Do not cover warning labels with
the loop tape.
5. Install the boat battery in the hull as shown.
3
5
Impulse 31
1. Turn the hatch lock counterclockwise to unlock the latch.
2. Lift the back of the hatch and pull the hatch backward to remove.
3. Remove the radio box cover.
2 3
4. Put hook tape inside the boat hull as shown.
5. Put loop tape on the boat battery. Do not cover warning labels with
the loop tape.
6. Install the boat battery in the hull as shown.
5
6
• Fully charge the battery pack(s) before installing the pack(s)
in the boat.
• Do not charge any battery unattended, and monitor for heat.
• If the battery pack is more than warm to the touch, immediately
discontinue charging.
• Follow all safety precautions and instructions supplied by the
battery charger and battery manufacturer.
Only use high
performance batteries. We recommend using Pro Boat Ni-MH battery
packs (PRB3316). Low quality or unmatched battery packs will not deliver
the amount of power needed to operate the boat. If the Ni-MH batteries
are fully charged and the ESC stops operating early, the most likely cause
is batteries with high internal resistance. It may be necessary to replace
batteries to ensure proper operation.
You may use (2) 7.2V Ni-MH batteries to operate the
Impulse 31. Before using Ni-MH batteries in the Impulse 31,
you must use the Pro Boat Brushless ESC Programming Module
(not included) to program the proper low voltage cutoff.
Turn the throttle trim knob to stop the propeller from turning while
the throttle trigger is in the neutral position.
Turn the rudder trim knob to center the rudder prior to operating
the boat. Adjust the rudder trim to make the boat run straight
during operation.
Dual Rate
Steering Trim
Throttle Trim
- Impulse 26 • Impulse 31 1
- 2
- 2
- 4
- 4
- 5
- 5
- 5
- 6
- 6
- 7
- 8
- 8
- 9
- 9
- 10
- 10
- Bedienungsanleitung 11
- Spezifikationen 12
- Einleitung 12
- Einbau des Antennenrohrs 14
- Zusammenbau des Bootständers 14
- Einlegen der Senderakkus 14
- Einlegen des/der Akkupacks 15
- Akkus und Aufladung 15
- Trimmeinstellung 15
- Anpassung des Handling 16
- Überprüfung des Funksystems 16
- Bootstest im Wasser 17
- Wartung 17
- Konformitätshinweise 19
- Kontaktinformationen 19
- Manuel de l'utilisateur 20
- Caractéristiques 21
- Introduction 21
- Impulse31 23
- Réglage de trim 24
- Ajustement du maniement 25
- Contrôle du système radio 25
- Maintenance 26
- Garantie et Réparations 27
- Coordonnées (pièces) 27
- Déclaration de Conformité 28
- Manuale dell'utente 29
- Ulteriori precauzioni per 30
- Specifiche 30
- Introduzione 30
- Impulse 31 32
- Installare il timone e le ali 32
- Precauzioni per la batteria 33
- Regolazione del trim 33
- Gestione della regolazione 34
- Controllo del sistema radio 34
- Manutenzione 35
- Impulse 26 36
- Durata della Garanzia 38
- Recapiti dei distributori 38
- Informazioni per i contatti 39
- ©2011 Horizon Hobby, Inc 40
- Printed 7/2011 31341 40
Powiązane produkty i podręczniki dla Zabawki zdalnie sterowane ProBoat Impulse 31 PRB4250B
(16 strony)
(44 strony)
Stemco Bearing Removal podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Do samochodu Stemco Bearing Removal.
Dostarczamy 1 pdf podręczników Stemco Bearing Removal do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Komentarze do niniejszej Instrukcji